Slip-On Scuba Webbing Hardware & Tri-Glides | Piranha Dive

So we have been working on our latest piece of hardware for almost a year!

You can now add this piece onto a harness without removing everything off to slide on your new piece!

This will work with any 1" inch" webbing soft "standard" or our stiffer webbing is not a problem

We also tumbled these for 48 hours to give them an ultra soft edge and will not cut or damage your webbing

Made from marine grade 304 stainless steel so you know it will not rust for a longer life!

Oh do not forget about our removable pin D-Rings located in our hardware section for a quick way to add to your rig!

Lastly we added holes for both 1/8" & 3/16" bungee or latex tubing if you want!

Overall length is just under 1 7/8" inches!

Loop length is 1" inch

Width is 1" inch

Thickness 1/8" inch

Made right here in the good ole Usa!

So we here at Piranha just added more to our slip-on hardware to make your life easier

You can now add this piece onto a harness without removing everything off to slide on your new piece!

This will work with our 2" webbing soft "standard" or our stiffer webbing not a problem

We also tumbled these for 48 hours to give them an ultra soft edge and that will not cut or damage your webbing

We also added a couple of holes so you can add bungee / Latex tubing if you wish too! 1/8" on the smaller holes or 3/16" on the larger holes!

Made from marine grade 304 stainless steel so you know it will not rust for a longer life!

Overall Width: 3" Inches

End Loop Length ID" 1" inch

Thickness: 1/8" inch

Select from our drop down box below if you want your hardware with either a slight bend on the loop or a 90 degree bend on the loop

If you want the loop part to be on the leftside select Left and if you want the loop on the right you would select rightside. The loop is built to be as you look down when wearing it.

So here we have a new D-Ring with a slot opening at the bottom thus allowing you to slide your webbing inside the D-Ring.

These work awesome with our slip on hardware allowing you more custom rigging of your dive set-up

This is a 6mm thick D-Ring

Fits all 2" inch wide webbing

So we here at Piranha just added more to our slip-on hardware to make your life easier

This will work with our 2" webbing soft "standard" or our stiffer webbing not a problem

We added a slight bend on the D-ring part to allow you to clip off easier!

We also tumbled these for 48 hours to give them an ultra soft edge and that will not cut or damage your webbing

We also added a couple of holes so you can add bungee / Latex tubing if you wish too! 1/8" on the smaller holes or 3/16" on the larger holes!

Made from marine grade 304 stainless steel so you know it will not rust for a longer life!

Overall Width: 3" Inches

D-Ring Depth: 1" inch

Thickness: 1/8" inch

So we here at Piranha just added more to our slip-on hardware to make your life easier

This will work with our 2" webbing soft "standard" or our stiffer webbing not a problem

We also tumbled these for 48 hours to give them an ultra soft edge and that will not cut or damage your webbing

We also added a couple of holes so you can add bungee / Latex tubing if you wish too! 1/8" on the smaller holes or 3/16" on the larger holes!

Made from marine grade 304 stainless steel so you know it will not rust for a longer life!

Overall Width: 3" Inches

D-Ring Depth: 1" inch

Thickness: 1/8" inch

So we here at Piranha just added more to our slip-on hardware to make your life easier

This will work with our 2" webbing soft "standard" or our stiffer webbing not a problem

We also have our webbing grabbing teeth that will not cause damage to your webbing but give you a slightly better lock onto your webbing!

We added our special gripping teeth that allows your webbing to hold onto our hardware yet not damage or cut your webbing!

We also tumbled these for 48 hours to give them an ultra soft edge and that will not cut or damage your webbing

We also added a couple of holes so you can add bungee / Latex tubing if you wish too! 1/8" on the smaller holes or 3/16" on the larger holes!

Made from marine grade 304 stainless steel so you know it will not rust for a longer life!

Overall Width: 3" Inches

D-Ring Depth: 3/4" inch

Thickness: 1/8" inch

So we have been working on our latest piece of hardware for almost a year!

You can now add this piece onto a harness without removing everything off to slide on your new piece!

This will work with our 2" webbing soft "standard" or our stiffer webbing is not a problem

We also tumbled these for 48 hours to give them an ultra soft edge and will not cut or damage your webbing

We also added a couple of holes so you can add bungee / Latex tubing if you wish too! 1/8" on the smaller holes or 3/16" on the larger holes!

Made from marine grade 304 stainless steel so you know it will not rust for a longer life!

Oh do not forget about our removable pin D-Rings located in our hardware section for a quick way to add to your rig!

You can select flat or slight bent version

Overall length is just under 4" inches!

Loop length is 1 1/8" inch

Width is 1" inch

Thickness 1/8" inch

Made right here in the good ole Usa!

So we have been working on our latest piece of hardware for almost a year!

You can now add this piece onto a harness without removing everything off to slide on your new piece!

This will work with our 2" webbing soft "standard" or our stiffer webbing is not a problem

We also tumbled these for 48 hours to give them an ultra soft edge and will not cut or damage your webbing

Made from marine grade 304 stainless steel so you know it will not rust for a longer life!

Oh do not forget about our removable pin D-Rings located in our hardware section for a quick way to add to your rig!

Lastly we added holes for both 1/8" & 3/16" bungee or latex tubing if you want!

Overall length is just under 3" inches!

Loop length is 1 1/8" inch

Width is 1" inch

Thickness 1/8" inch

Made right here in the good ole Usa!

So we here at Piranha just added more to our slip-on hardware to make your life easier

This will work with our 2" webbing soft "standard" or our stiffer webbing not a problem

We also tumbled these for 48 hours to give them an ultra soft edge and that will not cut or damage your webbing

We also added a couple of holes so you can add bungee / Latex tubing if you wish too! 1/8" on the smaller holes or 3/16" on the larger holes!

Made from marine grade 304 stainless steel so you know it will not rust for a longer life!

Overall Width: 3" Inches

D-Ring Depth: 3/4" inch

Thickness: 1/8" inch

So here we have a new D-Ring with a slot opening at the bottom thus allowing you to slide your webbing inside the D-Ring.

These work awesome with our slip on hardware allowing you more custom rigging of your dive set-up

This is a 5mm thick D-Ring

Fits all 2" inch wide webbing

One of our latest d-rings to come in to Piranha!

This is a 5mm thick d-ring for strength and durability

This d-ring we have a gap so you can slid onto your harness for a quick attachment. Yes just go to our hardware tab and look for our slip on hardware there you can get a slip on tri-glide to go with this d-ring if you have a harness built already and if not then your world gets a little easier to work with

We have a slight bend to allow you to quickly find this d-ring when diving in dark or murky environments

One of our latest d-rings to come in to Piranha!

This is a 5mm thick d-ring for strength and durability

This d-ring we have a gap so you can slid onto your harness for a quick attachment. Yes just go to our hardware tab and look for our slip on hardware there you can get a slip on tri-glide to go with this d-ring if you have a harness built already and if not then your world gets a little easier to work with

You are purchasing are FLAT / STRAIGHT version with an open slot!

One of our latest d-rings to come in to Piranha!

This is a 5mm thick d-ring for strength and durability

This uses a tri-angle design with a closed center

You are purchasing are FLAT / STRAIGHT version with an CLOSED CENTER SLOT!

One of our latest d-rings to come in to Piranha!

This is a 5mm thick d-ring for strength and durability

This uses a tri-angle design with a closed center and the lower end has a slight 30 degree bewn allowing for an easy clip off

You are purchasing are 30 Degree BEND version with an CLOSED CENTER SLOT!

So we here at Piranha just added more to our slip-on hardware to make your life easier

You can now add this piece onto a harness without removing everything off to slide on your new piece!

This will work with our 2" webbing soft "standard" or our stiffer webbing not a problem

We also tumbled these for 48 hours to give them an ultra soft edge and that will not cut or damage your webbing

We also added a couple of holes so you can add bungee / Latex tubing if you wish too! 1/8" on the smaller holes or 3/16" on the larger holes!

Made from marine grade 304 stainless steel so you know it will not rust for a longer life!

Overall Width: 3" Inches

End Loop Length ID" 1" inch

Thickness: 1/8" inch

Select from our drop down box below if you want your hardware with either a slight bend on the loop or a 90 degree bend on the loop

If you want the loop part to be on the leftside select Left and if you want the loop on the right you would select rightside. The loop is built to be as you look down when wearing it.