Scuba Transfill Whip Hoses & Gauges | DIN | Piranha Dive

• 2 x 9/16-18 (adapters) Male lnlets : These are located at the top in the picture and they have the red caps on them! These are screw into the block and may be removed to use 3/8-24 female ports
• 1 x 3/8-24 Female outlet
• Made from a solid brass block and then electro-plated for a protective finish!
• knob is made out of high quality aluminum and is anodized black! Also ribbed to work with or without gloves on easy
• Inlet adapters can be removed to expose 3/8-24 female ports
• Light weight design as this little block comes in at: 534g / 1.17 Pounds
• This block allows a diver to change between two separate air tanks without having to remove Their full face mask and the knob can turns a full 180 degrees
• This is set up for a left side application
• This part is NITROX READY right out of the packaging!

• Our transfill whip has 300 bar DIN connectors on each end so you can fill to any din system
• Our Gauge is oil filled to ensure accuracy
• Large 2" inch gauge face makes reading easy and simple in either PSI or BAR!
• Gauge has both PSI and BAR Scale in 100 PSI increments
• Our high pressure hose is roughly 60" inches long and is made out of a tough kevlar inner braided material with a poylmer outer shealth
• Rotating bleed valve knod located just under the gauge allows you to maintain a high accuracy and better control when filling your cylinders
• This is our larger bore transfill hose in diameter which will allow you to move your air / mix faster from one cylinder to another! 
• You can use our whip in multiple ways such as to equalize cylinders, transfill from "doubles banks" or filling smaller rebreather bottles
• ***NOTICE: Our whips are sent with the pressure gauge not conntacted to protect from damage during shipping! You just remove the one port plug and screw in the gauge.. DO NOT USE teflon tape or anything on the threads just screw it in! 

• Our transfill whip has 300 bar DIN connectors on each end
• Our new pony bottle gauge is smaller and simpler to handle but still has an high accuracy
• Our pony bottle gauge face makes reading easy and simple in either PSI or BAR! The color coding makes looking at where you are with your transfill simple!!
• Gauge has both PSI and BAR Scale in 100 PSI increments with a color fill bar graph
• Our high pressure Large Bore hose is roughly 60" inches long
• Rotating bleed knob located near the pony gauge allows for easy control of your fill
• You can use our whip in multiple ways such as to equalize cylinders, transfill from "doubles banks" or filling smaller rebreather bottles
• NOTE: You are purchasing a large bore hose which moves the air much faster then our braided hose transfill whips 

• Our transfill whip has 300 bar DIN connectors on each end
• Each Gauge is oil filled to ensure accuracy and durablility
• Large gauge face makes reading easy and simple in either PSI or BAR!
• Gauge has both PSI and BAR Scale in 100 PSI increments
• Our high pressure hose is roughly 60" inches long
• Bleed valve at the bottom of the SPG guage area allows you to maintain a high accuracy and better control when using
• You can use our whip in multiple ways such as to equalize cylinders, transfill from "doubles banks" or filling smaller rebreather bottles
• Note: This whip moves your gas slower than our standard whip so please keep this in mind when purchasing. Uses a smaller bore hose which allows gas to move from 1 cylinder to another just at a slower rate!
• ***NOTICE: Our whips are sent with the pressure gauge not conntacted to protect from damage during shipping! You just remove the one port plug and screw in the gauge.. DO NOT USE teflon tape or anything on the threads just screw it in! 

• Our transfill whip has 300 bar DIN connectors on each end
• There is NO GAUGE with this part! HOSE ONLY
• Our high pressure BRIADED hose is roughly 60" inches long
• Bleed valve at the bottom of the SPG guage area allows you to maintain a high accuracy and better control when using
• You can use our whip in multiple ways such as to equalize cylinders, transfill from "doubles banks" or filling smaller rebreather bottles
• NOTE: Transfilling with this whip the air moves very slow between the cylinders! If you want or need a quicker transfer go with the large bore 

• 2 x 9/16-18 (adapters) Male lnlets : These are located at the top in the picture and they have the red caps on them! These are screw into the block and may be removed to use 3/8-24 female ports
• 1 x 3/8-24 Female outlet
• Made from a solid brass block and then electro-plated for a protective finish!
• knob is made out of high quality aluminum and is anodized black! Also ribbed to work with or without gloves on easy
• Inlet adapters can be removed to expose 3/8-24 female ports
• Light weight design as this little block come in at: 534g / 1.17 Pounds
• This block allows a diver to change between two separate air tanks without having to remove Their full face mask and the knob can turns a full 180 degrees
• This is set up for a right side application
• This part is NITROX READY right out of the packaging!

BOV Quick Disconnect kit

• Our kit includes one locking quick disconnect AB-04 connector and we marry that with our LH-A regulator side connection 9/16 fitting but you MUST select which fitting you wish with your kit! Choose down below!!
• NOTE: You can now select either fitting from our drop down box below to complete your set-up

  Detailed Information

• Quick disconnect for BOV or second stage regulator
• Also check out our newest adapter our Deluxe LH-A adapter! Its costs very little to upgrade to our best adapter yet!
• Female 9/16 thread on our LH-A connector NOTE: The nipple to screw on the BOV or second stage
• Male 9/16 thread on locking AB-04 Quick Disconnect locking slider to screw on standard low pressure regulator hoses
• Our AB-04 quick disconnet locking slider is sealed shut when disconnected for added safety. We use a locking ring mechanism protecting against accidental disconnection during a dive!

BOV Quick Disconnect kit with non-locking connector system